Vial Label Size Chart: 2ml, 5ml, 10ml, 20ml and 30ml Vials
Getting vial labels right starts with three numbers—body diameter, usable height, and wrap width.
The specification indicated on a vial label is not determined by the vial’s nominal fill volume. A “10ml vial” from one supplier can be a millimeter or two wider than another, and that difference is enough to make a full-wrap label overlap or curl at the seam.
This chart gives you a practical starting point for 2ml through 30ml vials, plus a two-minute method to confirm dimensions on your own stock.
Vial Label Size Chart: 2ml, 5ml, 10ml, 20ml and 30ml Vials
How to read this chart
Before touching the vial label size chart numbers, clarify three terms used throughout the table.
OD (outer diameter) is the measured width across the vial body, not the cap or other parts. For labeling, use the diameter at the flat, cylindrical section where the label sits. Neck and cap dimensions are irrelevant here.
Usable height is the vertical space between the bottom of the threads (or neck shoulder) and the start of the bottom curve. Labels that creep into the curved shoulder or base tend to lift at the edges, especially on small 3ml vials. Leave 3~4 mm of buffer at both ends. This also makes it easier to apply labels to the bottles.
Wrap width and overlap allowance
A full-wrap vial label width is not simply circumference. Calculate circumference as OD × π, then subtract 5~8 mm for a clean seam gap. If you prefer a slight overlap for security, add 2–3 mm instead, but for small 3 mL vial labels, it is best to avoid any overlap, as this makes the edges prone to lifting.

The master chart
The dimensions below are typical starting points drawn from common glass vial specifications and label supplier guidance. Treat them as baseline estimates: your specific vial mold may differ by 1–2 mm.
| Vial size | Body OD (mm) | Usable height (mm) | Full-wrap width (mm)* | Full-wrap height (mm) | Recommended label size (mm) |
| 2ml | 12–16 | 15–22 | 37–50 | 20–25 | 18 × 40, 20 × 50 |
| 5ml | 18–22 | 15–22 | 56–69 | 20–25 | 18 × 50, 20 × 50, 20 × 60 |
| 10ml | 22–25 | 25–35 | 69–78.5 | 35–40 | 25 × 60, 30 × 60, 30× 65 |
| 20ml | 26–30 | 30–45 | 81–92 | 38–50 | 30 × 70, 35× 75 |
| 30ml | 30–33 | 48–55 | 94–101 | 42–50 | 30 × 80, 45× 90 |
For reference, a standard 10ml tubular glass vial often measures around 22 mm OD with roughly 50 mm total height, leaving about 25–35 mm of usable straight wall after accounting for neck and base curves.
A 2ml glass vial in one measures 16 mm OD with a 24 mm label panel height. These real-world examples sit within the ranges above, but the variation is precisely why measurement matters.
2ml and 5ml vials
A 2ml vial with a 16 mm OD gives you a printable width of 40–45 mm and a height under 30 mm.
A logo, product name, concentration, batch number, and expiry date, these elements are indispensable parts of the label. It would be best for us to make each text as large as possible and keep the content concise, so that the content on the label can be easily read.
The recommended size for a 5ml vial label is 20 x 60 mm.
The dimensions of the 5ml and 2ml labels are quite similar. Since these small bottles have limited space, we focus on including only essential information on the label, such as product name, dosage, and expiration date.
10ml vials
The 10ml vial is the most commonly used small-volume pharmaceutical and diagnostic packaging.
A typical 10ml tubular vial measures 22–25 mm OD and about 50 mm in total height. The usable straight wall is usually 30–35 mm tall. A full-wrap label at 60–75 mm wide × 25–35 mm high fits comfortably, with enough seam gap to avoid overlap and enough top/bottom clearance to prevent edge lift.
If you are labeling by hand, a slightly narrower label (25 x 60 mm) is more forgiving of placement error. If you are running automated equipment, please confirm the label size, label materials that the machine can use, and the direction and size of the labels; but a 1 mm width error of vial labels is less likely to cause a jam than an adhesive that releases too slowly or too quickly.
Whether it is manual labeling or automatic labeling, having a certain gap when the label is applied to the bottle is more aesthetically pleasing and more convenient to use.
For the shorter 10ml vial, we recommend a label size of 25 x 60mm.
For the taller 10ml vial, we recommend a label size of 30 x 60mm.
Customers can adjust to their preferred label sizes within a certain range.
For content, the 10ml label can accommodate brand name, logo, a product name, dosage, volume, batch, expiry, and barcode, but only if the design is disciplined. It is even possible to add scannable QR codes, random codes, and scratch-off layers.
Keep the product name in a single line of vision where possible; regulatory guidance for small-volume containers emphasizes that critical information should be visible without rotating the vial. On a 22mm diameter 10ml vial, that means prioritizing the name and dosage above all else. Other content can be placed on the left and right parts of the label.

20ml and 30ml vials
The jump from 10ml label size to 20 ml label size is not linear.
A 20ml vial typically moves to a 26–30 mm OD, which increases circumference from about 80 mm to about 90 mm. That extra 15 mm of width is meaningful: it allows a larger font for the product name, a scannable linear barcode, and a clearer separation between cautionary text and dosing information.
Customers can display more information about the product and the brand on the vial label, and add more special production processes.
A 30ml vial at 30–33 mm OD gives you a wrap width of roughly 94–101 mm and usable height of 48–55 mm.
At this point, the label starts to behave like a small carton panel. You can fit full regulatory symbols, more manufacturer information, more icons and a clear QR code without crowding.
30ml vials often have a more pronounced shoulder and base radius, so verify usable height before ordering a 30ml vial label.
Customers can design labels with greater precision while maintaining a professional appearance.
For 30ml labels, there is sufficient height and width for detailed design, allowing customers to focus more on aesthetic dimensions.

Why the “same” 10ml vial can differ by 1–2 mm between suppliers
A “10ml” designation refers to nominal fill volume, not external geometry.
For a 10ml bottle, each supplier has its own dedicated mold size. The 10ml refers to the volume of product the bottle can hold, not the actual dimensions of the bottle. Two suppliers can both sell a 10ml vial where one measures 22 mm OD and the other 24 mm—a difference invisible to the eye but significant for a full-wrap label. The 24 OD vial can fit a 75 mm-wide label, but the 22mm OD can only fit labels smaller than 70mm. Order the wrong one and you either get an overlapping label or a label that is placed on the bottle with a large gap.
During the production process of glass vial, many factors can affect the bottle body diameters, such as raw materials, the usage time of molds, temperature, etc.
Even for the same glass vial supplier using the same mold, different batches of vials will have some production errors, which is a very normal situation.
The reliable solution is to measure the vials you will actually be labeling, and record the specific 10ml label size that you like.
And within a certain range, the labels can be reduced by 1 to 2 mm. This ensures that even if there is a certain size error among different batches of glass vials, the labels can still be used.

How to measure your own vial in 2 minutes
You need three things: a ruler with millimeter markings, a strip of paper about 10 cm long, and a pen.
Step 1: Measure the OD.
Place the vial on a flat surface. Use the ruler to measure across the widest part of the cylindrical body, not the cap or neck. Note the number in millimeters.
The diameter of the vial is the most crucial factor in determining the width of the label.
Step 2: Measure the usable height.
Measure from the bottom edge of the threads (or the neck shoulder, if there are no threads) down to the point where the glass begins to curve inward at the base. Do not include the curved sections.
The height of the label can be appropriately reduced by 3 to 5 mm based on the measurement. This reduced height makes it easier and more convenient to attach the label to the vial.
Step 3: Measure the circumference with the paper strip.
Wrap the paper around the vial body section, mark where the paper overlaps itself, and lay it flat against the ruler. This is your true circumference.
Step 4: Calculate label width.
Circumference minus 3~5 mm (for a seam gap) is your maximum full-wrap width.
If you want a small overlap instead, add 2~3 mm.
Step 5: Test before printing.
If you have a printer, print your label on plain paper, cut it to size, and wrap it around the actual vial. Check for overlap and gaps. Adjust before committing to a bulk production.
If you don’t have a printer, you can also cut out a blank piece of paper of the size you need for the label and conduct a size test.
There is also a very simple way to confirm the size of the label.
You can directly contact your bottle supplier and ask for the exact data on the diameter and height of the bottle, and also inquire if they have any recommended label sizes.
Download the vial label size template (PDF)
vial-label-size-chart-brand name.pdf
The above is the design template for our most commonly produced 2ml (3ml) and 10ml vial labels.
Customers can directly download the PDF file above and create the designs.
The design files need to have at least 3mm bleed area and should be saved in a modifiable vector file format after the design is completed. The clearer the file, the better the printing effect of the labels will be.
However, the vial label size of the above PDF file is not a fixed size. Customers can adjust it according to the specific size of their bottles and their own preferences. We can provide the design template files separately to the customers.
We can also offer free design services to customers.

FAQ
What is the standard size of a vial label?
There is no single standard. Label size is determined by the vial’s OD and usable height, not its nominal volume. A full-wrap label for a 10ml vial is typically around 60-70 mm wide × 25-30 mm high, but this varies by manufacturer.
Please measure your specific vial before specifying a label.
How do I know what size label my vial needs?
According to the method of label size confirmation we mentioned above, measure the body OD and usable height, calculate circumference (OD × 3.14), subtract 3~5 mm for a seam gap, and choose a label height that leaves 2~3 mm clearance from the threads and base curve. Test a paper cutout on the actual vial before ordering.
Are vial labels measured in mm or inches?
Both are used. Convert with 1 inch = 25.4 mm when comparing specifications.
Pharmaceutical and laboratory suppliers often specify vials in millimeters, while some label stock (especially in the US) is sold in inches. Most label converters can produce either, and many charts provide both columns.
What size label fits a 10ml vial?
A common starting point is a 60-65 mm wide × 25-30 mm high full-wrap label.
For 10ml vial bottles with a roughly 22 mm OD, a 2.7″ × 1.2″ (68 × 30 mm) label provides a near-full wrap.
Do you need a complete vial size chart?
Please contact us to confirm the size of the labels you need and obtain the actual samples.


Leave a Reply
Want to join the discussion?Feel free to contribute!